Installation Guides& Videos

Page Title - Swoosh

Toilet Seat Installation is Fast and Easy

Typically, the most difficult job of replacing a seat is removing the old one, but with a standard wrench, a screwdriver and a spray can of WD-40® penetrating oil, you'll find it quite easy.

Typically, the most difficult job of replacing a seat is removing the old one. Depending on the seat you own, it can be removed with either a screwdriver or a wrench. Remember, your tools are steel and can easily chip the bowl, which is porcelain. If the bolts are rusty or badly calcified, you can spray them with WD-40® penetrating oil, but use only if you do not intend to use the seat again. Let the oil sit for five or ten minutes, and then try loosening the bolts again. If they still won't move, you might want to consider calling a professional.

Next, refer to the installation instructions included with your toilet seat or use the links below.

Common Toilet Seat Installation

Your common toilet seat is usually very basic and easy to install.

Common installation images
  1. Remove the old seat using the instructions above
  2. Place new toilet seat on the toilet bowl with the hinges over the bolt holes in the toilet bowl
  3. Easily open hinge caps (Do not pry hinge caps off! If the caps have two "ears" on each upper side of the cap, your seat likely installs a different way. See Easy•Clean & Change™ below.)
  4. Drop the bolt through the open hinge and bolt hole
  5. Screw the bolt nut around the bolt until tight.

NextStep® Built-In Potty Seat

View the NextStep® with STA-TITE® instruction guide or watch the video:

Easy•Clean & Change™ Hinges (Standard)

If you have a standard Easy•Clean & Change™ hinge, you can follow these 4 simple steps to install your toilet seat. Also, You can view the Easy•Clean & Change™ instruction sheet.

Do not remove the hinge caps!
  1. Install Bolt.
    Put bolt through bowl, screw-in nut.

  2. Unlock Hinge.
    Turn hinge cap to the left.

  3. Attach Seat.
    Press unlocked seat hinges onto bolts.

  4. Lock Hinge.
    Turn hinge cap to the right.

View the Easy•Clean & Change installation video.

Easy•Clean & Change™ Hinges with Sta-Tite®

If you have a Easy•Clean & Change™ Hinge with Sta-Tite®, you can follow these simple steps to install your toilet seat.

Also, You can view the Easy•Clean & Change with Sta-Tite® instruction sheet.

Do not remove the hinge caps!
  1. Unlock Hinge Caps.
    Twist hinge cap to the left.

  2. Click Bolt Into Hinge.
    Put bolt head into the hinge until you hear a click.

  3. Lock Hinge Caps.
    Twist hinge cap to the right to lock bolt into hinge.

  4. Place Toilet Seat
    on Bowl. Place bolt through bowl mounting holes.

  5. Center Toilet Seat.
    Hold the toilet seat center throughout the process.

  6. Install Sta-Tite® Nut.
    Hand-tighten first.

  7. Break Sta-Tite® Nut.
    Tighten Sta-Tite® Nut with wrentch until bottom breaks off.

View the Easy•Clean & Change with Sta-Tite® installation video.

Standard metal hinge with residential Sta-Tite®

If you have a metal hinge with Sta-Tite, you can follow these 6 simple steps to install your toilet seat. Also, You can view the Residential Sta-Tite® Metal Hinges instruction sheet.

  1. Thread the bolt into the hinge.

  2. Push the bushing all the way up bolt until it's flush with the hinge.

  3. Place toilet seat bolts into toilet bowl.

  4. Finger-tighten Sta-Tite® nut onto bolts.

  5. Align toilet seat onto bowl and use a 1/2" wrench to tight bolt.

  6. Bolt head will snap off when the precise tightness is reached.

Whisper•Close® metal hinge with residential Sta-Tite®

If you have a pre-threaded metal hinge, you can follow these 6 simple steps to install your toilet seat. Also, You can view the Residential Sta-Tite Metal Hinges instruction sheet.

  1. Thread the bolt into the hinge.

  2. Push the bushing all the way up bolt until it's flush with the hinge.

  3. Place toilet seat bolts into toilet bowl.

  4. Finger-tighten Sta-Tite nut onto bolts.

  5. Align toilet seat onto bowl and use a 1/2" wrench to tight bolt.

  6. Bolt head will snap off when the precise tightness is reached.